Venturis – for Wood

Available to order
Price: 3300 (XL) or 3900 EUR (XXL)
(+VAT tax 20%)

---

• Working area:
  1250 x 2500 x 120 mm (XL)
  1500 x 3000 x 120 mm (XXL)
  Other, custom sizes possible
• Max speed: over 12000 mm/min (X and Y)
• Repeatability: better than 0,01mm
  
• Suitable for: woods and plastics, but can also cope with softer metals.
  
  
  
  
  
  
  

---

• Transmission:
  • Y-axis: strong steel-reinforced timing belts (x2), width 15mm;
  • X-axis: strong steel-reinforced timing belt, width 15mm;
  • Z-axis: 1204 ballscrew.

• Rails and carriages:
  • Y-axis: double-row V-slot bearings on aluminium bars;
  • X-axis: ball bearings on stainless steel 50x50mm square tubes;
  • Z-axis: MGN12 linear rails and carriages.
    
    
• Control electronics:
  • Independent system – does not require a PC to operate.
  • Two 32-bit processors;
  • Colour 3.2″ touchscreen;
  • SD-card reader + WiFi;
  • Joystick;
  • Controller enables adding a fourth and fifth axis in the future (for example – a horizontal “lathe type” spindle, automatic tool change etc.).
    
    
• Transmission motors:
  • Nema 23 motors;
  • 3-phase, 48V
  • X- and Y-axis 3Nm, 200W
  • Z-axis 2Nm, 150W
  • Servo-like, so-called “hybrid stepper motors” (position sensors on axle with electronic position correction if needed).
    
    
    
• Frame, legs and gantry:
  very rigid “torsion-box” type spaceframe of high-quality, waterproof 15mm Baltic Birch plywood.
  
  
• Spindle:
  • Brushless spindle with variable frequency inverter;
  • Power 1,5kW;
  • Precise numeric speed control 0…24’000 RPM;
  • aircooled;
  • collet: ER11 (suitable for endmills 0,5…7 mm).

• Cable system:
  • full cabling – plug in and go.
  • grounded, double shielded.
  • Includes 2 cable chains.
    
    
• Dust shoe
  • connection for 100mm tubing
    
    
    
• Limit switches for all axes
  
  
• Probe for measuring stock surface
  
  
• One section of the table upper surface can be removed (ca 300×300 mm) – for placing taller stock, vises, or long vertical items

Venturis – for Alu

Coming soon
Price: 3900 EUR (+ VAT tax 20%)
 

---

• Working area:
  ca 600 x 900 x 100 mm
• Max speed: over 12000 mm/min (X and Y)
• Repeatability: better than 0,01mm
  
• Linear rails and ballscrews all around enable maintaining accurate position also under heavier cutting forces.
  Therefore, this model is suitable for aluminum and bronze (more than Venturis Wood), but can naturally also cut woods, plastics etc.
  
  

---

• Transmission:
  • Y-axis: 1605 ball screws (x2);
  • X-axis: 1605 ball screw;
  • Z-axis: 1204 ball screw.

• Rails and carriages:
  • Y-axis: HGR20 linear rails and carriages;
  • X-axis: HGR20 linear rails and carriages;
  • Z-axis: MGN12 linear rails and carriages.
    
    
• Control electronics:
  • Independent system – does not require a PC to operate.
  • Two 32-bit processors;
  • Colour 3.2″ touchscreen;
  • SD-card reader + WiFi;
  • Joystick;
  • Controller enables adding a fourth and fifth axis in the future (for example – a horizontal “lathe type” spindle, automatic tool change etc.).
    
    
• Transmission motors:
  • Nema 23 motors;
  • 3-phase, 48V
  • Y-axis 3Nm, 200W (x2)
  • X-axis 3Nm, 200W
  • Z-axis 2Nm, 150W
  • Servo-like, so-called “hybrid stepper motors” (position sensors on axle with electronic position correction if needed).
    
    
    
• Frame, legs and gantry:
  very rigid “torsion-box” type spaceframe of high-quality, waterproof 15mm Baltic Birch plywood.
  
  
• Spindle:
  • Brushless spindle with variable frequency inverter;
  • Power 2,2kW;
  • Precise numeric speed control 0…24’000 RPM;
  • aircooled;
  • collet: ER201 (suitable for endmills 1…13 mm).

• Cable system:
  • full cabling – plug in and go.
  • grounded, double shielded.
  • Includes 2 cable chains.
    

• Dust shoe
  • per request
    
    
• Limit switches for all axes
  
  
• Probe for measuring stock surface
  

Venturis – Industrial

Available to order
Price: from 6900 EUR (+ VAT tax 20%)
 

---

• Working area:
  1250 x 1500 x 120 mm
  1500 x 3000 x 120 mm
• Max speed: over 12000 mm/min (X and Y)
• Repeatability: better than 0,01mm
  
• Industrially produced CNC.
  Steel frame – welded, heat-treated and powder coated.
  Industrial-grade rigidity allows for deeper and faster cuts in aluminum, bronze, wood materials, plastics etc.
  
  
  
  

---

• Transmission:
  • Y-axis: Helical rack (x2);
  • X-axis: Helical rack;
  • Z-axis: TBI ball screw.

• Rails and carriages:
  • Y-axis: Hiwin linear rails and carriages;
  • X-axis: Hiwin linear rails and carriages;
  • Z-axis: Hiwin linear rails and carriages.
    
    
    
• Control electronics:
  • As per customers request: Mach3, DSP etc.
    
    
    
    
    
    
• Transmission motors:
  • 86BYG stepper motors or servos.
  • Leadshine drivers.
    
    
    
    
    
    
    
    
    
• Frame, legs and gantry:
  massive steel frame (welded, heat-treated, powder coated)
  
  
• Spindle:
  • Brushless spindle with variable frequency inverter;
  • Power from 3 kW;
  • Precise numeric speed control 0…24’000 RPM;
  • collet: as per customers request.

• Cable system:
  • needs 380 V.
  • Electric components by Schneider
    
• Dust shoe
  • connection for 100mm tubing
    
    
• Limit switches for all axes
  
  
• Probe for measuring stock surface
  
  
• Central lubrication system